Mike Nasiatka has built one of the gnarliest homebrew track creations we've ever seen, much less driven. Though he'd never built a car before, he began with two cars: a crashed 1994 Mitsubishi Eclipse GS-T drag car, and a second-generation Pontiac Fiero GT. By shoving the complete Eclipse drivetrain in the back of the Fiero, Mike has created an absolutely terrifying monster of a car. The engine runs a 68MM Precision Turbo and on 35 PSI makes 700 horsepower, but, thankfully, Mike agreed to dial it back to 20 PSI for my drive, with only 500 horsepower at the wheels. Hang on, because this is some ride. Check out Mike's Death Fiero on Facebook! https://www.facebook.com/groups/820867661318361/ Build Sheet: Engine New 6 bolt 4g63 block and head standard bore 2.0 liter Eagle crank and rods Ross racing pistons 8.5:1 compression Stock mitsu oil pump Balance shaft deleted Cylinder head race ported Brian crower 272 cams Brian crower valve train Kiggly hla Custom built -10 crankcase vent and recirculating catch can setup Dnp tubular turbo manifold Tial 38 mm wastegate with external side dump Precision 6768 dual ball bearing turbo Sail panel mounted cool air intake Top mount Dual 3inch exhaust 2.5 inch stainless charge pipe Large slowboy racing front mount intercooler (rear mounted)(twin 10? cooling fans? 50mm tial Q blow off valve 75mm mustang cobra professional products throttle body Jmf style stainless intake manifold Utilizing 1990 dsm electronics Coil on plug ignition using Chrysler ignition coils Dyna arc 2 ignition amplifier Ecmlink v3 engine management software with a socketed Mitsubishi ecm Converted to speed density Running pump e85 4 Fuel injector clinic 1650cc stainless fuel injectors Magnus aluminum fuel rail -8 ptfe braided fuel lines Aeromotive inline fuel filter 15 gallon aluminum fuel cell with custom dual intank walbro 255?s Aeromotive 1:1 boost reference fuel pressure regulator Relocated 90 amp alternator External mishimoto oil cooler 3qt canton racing accusump unit Large mishimoto aluminum radiator Transmission Fwd Mitsubishi trans built by john shepard using 1g case with built 2g internals and quaife limited slip diff Axle shafts are custom driveshaft shop axles using customized J body gm hub bearings to fit the larger axle spline size with a more heavy duty flange Second gen eclipse electronic speed sensor Chassis Stripped down tube chassis 86 fiero gt Fitted with customized full length Megan racing coil over?s for a Mitsubishi eclipse fwd in reverse fronts in back and backs in front Custom built control arms in the front with tubular uppers and Rodney dickman upper and lower ball joints Factory fiero spindles modified for better engagement with ball joints Custom aluminum hub assemblies to drop weight and allow use of 12? c4 corvette brake components front and rear (pads calipers and rotors front and rear) Hawk hp plus pads Rear mounted optima battery Fiero steering rack modified mounting Modified fiero front cradle Modified solid mounted fiero rear cradle All custom engine mounts Rear tubular crash bar/chassis brace 12? led headlights/turnsignals Corvette style tail lights Relocated factory wing 6 inch rearward and solid molded to platform Hand made fiberglass open sail panels Hand made fiberglass one piece front end Handmade one off wide body 18? Rota p45 wheels 275/35/18 square setup direzza star specs Interior Kirky racing seats Rci camlock harnesses Aluminum steering wheel with quick connect steering shaft Painless switch panel Floor mounted willwood clutch and dual master brake pedal dual residual willwood check valves Customized roller style throttle Willwood master and custom hand brake Modified 1g dsm 5 speed shifter 1g dsm shifter cables Autometer gauges Gps speedometer Innovate scg-1 electronic boost controller and wideband